How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask Michael Your Own Question

Michael
Michael, Customer Service
Category: Appliance
Satisfied Customers: 9314
Experience:  I have been an appliance repair tech for over 30 years and will help you solve your problems.
11519491
Type Your Appliance Question Here...
Michael is online now

How do you reset the error code on a WAE24060GB washing ma

Resolved Question:

How do you reset the error code on a WAE24060GB washing machine?
Submitted: 2 years ago.
Category: Appliance
Expert:  Michael replied 2 years ago.
Hi what happened that you replaced the brushes?
Also are you sure the main control board is ok?
Please try this and let me know if this works for your machine or not, as there could be another issue.
I will stick with you until this is fixed but since this may take some time, if you will rate my service in a positive fashion thus far before you close this page, the system will allow me to schedule free follow ups with you and also ensure your question will NOT close or time out;-)
You will then be able to contact me at anytime at no additional cost until we have this fixed for you.

Thank you XXXXX
I've included a test program for your washer for you to use if you like to get a better diagnostic. Hope this helps.


Selecting the test program
Activate test
program:
Set program selector switch to OFF position
Press and hold the two buttons closest to the dial then turn the program selector counter-clockwise to the first program
position. Keep holding the buttons until the display shows P:01
Select test
program:
Push second button from dial to scroll through tests.
-P:01 -> Errors
-P:02 -> Safety test
-P:03 -> Automatic test sequence
-P:04 -> Motor
-P:05 -> Variant (not currently used)
-P:06 -> Display
-P:07 -> Buttons and selector switch
-P:08 -> Pressure sensor (not currently used)
-P:09 -> Pressure switch
-P:12 -> Update (not currently used)
-P:13 -> Valves
-P:14 -> Buzzer
-P:15 -> Pump
-P:16 -> Heater
-P:17 -> Noise (not currently used)
Start test
program:
Press START/PAUSE button
Abort test
program:
Press second button away from program dial or set program selector to Off position
Leave test
programs:
Switch off device
P:01 Errors
- Press Start/Pause to enter error feedback loop
- Press the second button away from the program dial to scroll through errors sequentially; error counts are displayed for
each error
- Error descriptions are given on Page 2 of this document
P:02 Safety test
Sequence: - Water fills to first level
- Heater is turned on for 30 seconds
P:03 Automatic Test
Time/s 4* 6 3 2 3 1 10 1 10 10 90
Valve 2 1 3 1+2
Heater
Water level
L1
Motor
CW rotation
Off
CCW rotation
50rpm
1150
rpm
End of program
Pumping X X X
* depends on pre-filling level and period until level 1 is reached
P:04 Motor
Test: Sequence:
Reversing - Counter-clockwise drum rotation at 50rpm
- Clockwise drum rotation at 50rpm
Spinning /
Pumping:
- Spin speed increases to max. speed
- Unbalance detection is disabled
- Only catastrophic unbaXXXXX XXXXXmits are checked
- Speed reduction is not possible
P:06 Display
All LEDs and all segments of the LCD display are tested
Test program runs automatically
Sequence:
- Backlight switched off (ME99)
- Start LED and options LEDs are activated
- Pause
- Backlight switched on (ME99)
- all LCD/LED segments are activated in particular order
- Successive activation of single segments in LCD display
P:07 Buttons and selector switch
Test: Sequence:
Buttons - By pressing a button, the associated LED will light up
- By pressing the Select button, the spin sign appears in LCD display (ME99)
Selector switch - When selecting each position on the selector switch, the serially numbered positions are displayed in LCD display
(Do not rotate PS via OFF, otherwise program abort)
P:09 Pressure Switch
Sequence:
- Pump is turned on until the drum is empty
- Valve 1 is turned on until first level is reached
- Pressure is displayed
P:13 Valves
- Each valve and valve combination is tested.
- Use the START button to step through the test sequence - each push activates the next valve
- Pressure (water level) is shown in the display
- program runs automatically until level Nmax is reached or second button from program dial is pressed
P:14 Buzzer
The buzzer is activated at maximum volume.
P:15 Pump
The pump is activated and runs a maximum time of 30min unless it is stopped by pressing the second button away from the
program dial.
P:16 Heater
The heater is activated as soon as the water level reaches the heating level and is runs a maximum time of 30min unless it is
stopped by pressing the second button away from the program dial. Water temperature is displayed during the program.
The NTC can be checked during this test
Michael, Customer Service
Category: Appliance
Satisfied Customers: 9314
Experience: I have been an appliance repair tech for over 30 years and will help you solve your problems.
Michael and other Appliance Specialists are ready to help you

What Customers are Saying:

 
 
 
  • You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future. Jimmy
< Previous | Next >
  • You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future. Jimmy
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C.
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C.
 
 
 

Meet The Experts:

 
 
 
  • Rob

    Rob

    Home Appliance Technician

    Satisfied Customers:

    420
    20 yrs. experience with a major worldwide manufacturer.
< Previous | Next >
  • http://ww2.justanswer.com/uploads/RO/royzee1/2012-10-11_16153_serviceengineers.64x64.jpg Rob's Avatar

    Rob

    Home Appliance Technician

    Satisfied Customers:

    420
    20 yrs. experience with a major worldwide manufacturer.
  • http://ww2.justanswer.com/uploads/NE/needapplianceparts/2012-11-9_15310_rickcannon.64x64.jpg Appliance Parts's Avatar

    Appliance Parts

    Home Appliance Tech

    Satisfied Customers:

    82
    Appliance tech since 1992. Factory authorized
  • http://ww2.justanswer.com/uploads/JG/jgrella16/2011-9-12_73730_justanswerheadshot.64x64.jpg Jon's Avatar

    Jon

    Home Appliance Technician

    Satisfied Customers:

    1535
    Home appliance technician with over 12 years experience.
  • http://ww2.justanswer.com/uploads/SE/secondhandheaven/2014-11-23_141828_lge.64x64.jpg George-Allsorts's Avatar

    George-Allsorts

    Home Appliance Technician

    Satisfied Customers:

    1123
    A whitegoods technician with 30+ years service in Domestic Appliance Service & Repair, and General Mechanical & Electrical Repair
  • http://ww2.justanswer.com/uploads/RE/repairman4734/2011-5-21_171048_FarrellPic.64x64.png repairman4734's Avatar

    repairman4734

    Home Appliance Technician

    Satisfied Customers:

    684
    Thank you for your question, it is appreciated
  • http://ww2.justanswer.com/uploads/drcool299/2008-12-16_113651_francis.jpg drcool299's Avatar

    drcool299

    Home Appliance Technician

    Satisfied Customers:

    22
    I have been an Appliance tech for the past 15 years. Worked on most of the branded appliances.
  • http://ww2.justanswer.com/uploads/AS/asterixt/2015-8-31_143917_pic.64x64.jpg Michael's Avatar

    Michael

    Customer Service

    Satisfied Customers:

    2970
    I have been an appliance repair tech for over 30 years and will help you solve your problems.
 
 
 

Related Appliance Questions