Hi, My name is ***** ***** it is my pleasure to assist you. I have read the instructions and if you have pressed the mode button until the mode you want to be in and nothing happens there might be something wrong with the circuit board the watch carries a warranty I would bring the watch back to the store you bought it from exchange the watch and have them set the watch for you so you know the watch is working properly. Also you can try taking the battery out wait about 10 minutes and then start fresh sometimes this will reset the circuit board. Thanks Mike
If you need further assistance, please don't hesitate to ask.PLEASE remember if you're satisfied with my answer rate my answer " OK SERVICE " or higher so I will be compensated by JustAnswer for helping you.
To set time, date, and options:
1) With time and date showing, press and hold
2) Current time zone (1, 2, or 3) ﬂashes. Press
to select time zone to set, if desired.
. Hour ﬂashes. Press
to change hour (including AM/PM); hold button to scan values
. Minutes ﬂash. Press
to change minutes
. Seconds ﬂash. Press
to set seconds to zero.
. Month ﬂashes. Press
to change month.
. Day ﬂashes. Press
to change day.
. Year ﬂashes. Press
to change year.
to set options. Press
to change value and then press
to go to
at any step to exit and save settings. Available options are 12- or 24-hour time format,
MM-DD or DD.MM date format, hourly chime beep for button presses, mode customization set (Select
"HIDE" for unwanted modes – they are removed from mode sequence).
If you hide a mode, you can turn it back on later using procedure above.
once and hold to see 2nd time zone. Press
twice and hold to see third
time zone. Continue to hold button for 4 seconds to switch to displayed time zone.
Press and hold
upcoming occasion (see description of Occasion mode). Release
and immediately press and hold again to see subsequent occasions.
This mode provides a chronograph (stopwatch) function. Press
to go to Chrono mode.
To start, press
. Chrono counts up by hundredths of a second up to one hour, then by
seconds up to 100 hours. Stopwatch icon w ﬂashes to indicate chrono is running.
To stop, press
. Stopwatch icon w freezes to indicate chrono is stopped.
To resume, press
, or to reset (clear) chrono, press and hold
When chrono is already running, chrono continues to run if you exit mode. Stopwatch icon w appears in
While chrono is running, press
to take a split. Lap and split times will be displayed with lap
Lap and split times are stored in memory until a new workout is started (chrono started from zero).
LAP 1 = 7.11
LAP 2 = 7.50
LAP 3 = 7.08
LAP 4 = 7.30
SPLIT 1 = 7.11
SPLIT 2 = 15.01
SPLIT 3 = 22.09
SPLIT 4 = 29.39
To recall split times during or after workout, press
. Then, press
to step through splits.
To set display format, press
while chrono is reset. Then, press
to select desired
• When a split is taken, times are frozen on the display for 10 seconds. Press
to release display
and show running chrono immediately.
to switch between recall and format setting.
Timer mode provides a countdown timer with alert. Press
repeatedly until TIMER appears.
To set countdown time:
. Hours ﬂash. Press
to change hours; hold button to scan values.
to change minutes.
to change seconds.
. Action at end of countdown ﬂashes. Press + or – to select STOP or REPEAT, indicated by
hourglass icon with arrow i .
at any step when done setting.
To start timer, press
. Timer counts down every second from countdown time. Hourglass
icon H ﬂashes to indicate timer is running.
To pause countdown, press
. Hourglass icon H freezes to indicate timer is stopped.
To resume countdown, press
, or to reset countdown, press
Watch beeps and night-light ﬂashes when countdown ends (timer reaches zero). Press any button to
silence. If REPEAT AT END was selected, timer repeats countdown indeﬁnitely.
Timer continues to run if you exit mode. Hourglass icon H appears in Time mode.
The watch has three alarms. Press
repeatedly until ALM 1, ALM 2, or ALM 3 appears.
To set alarm:
to change hour; hold button to scan values.
. AM/PM ﬂashes if in 12-hour time format. Press
. Alarm day setting ﬂashes. Press
to select DAILY, WKDAYS, or WKENDS.
To turn alarm on/off, press
Alarm clock icon a appears when alarm is on in this mode and in Time mode.
When alarm sounds, night-light ﬂashes. Press any button to silence. If no button is pressed, alarm will
sound for 20 seconds and repeat once ﬁve minutes later.
Each of the three alarms has a different alert melody.