How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • Go back-and-forth until satisfied
    Rate the answer you receive.
Ask NILESH PANCHAL Your Own Question
NILESH PANCHAL
NILESH PANCHAL, Engineer
Category: Printers
Satisfied Customers: 2296
Experience:  7 years of programming experience and Microsoft technologies expert
108438151
Type Your Printers Question Here...
NILESH PANCHAL is online now

Pixma mg6350 error msg B200, Yes, No idea sorry, No

Customer Question

Pixma mg6350 error msg B200
JA: Is your printer displaying the error on all print jobs, even after you restart it?
Customer: Yes
JA: When did you last update the printer driver software?
Customer: No idea sorry
JA: Anything else you want the Printer Expert to know before I connect you?
Customer: No
Submitted: 9 days ago.
Category: Printers
Expert:  NILESH PANCHAL replied 9 days ago.

Hello and Welcome to JustAnswer, an independent Question and Answer site. My name is ***** ***** I will be happy to assist you today!

For the Error Code B200 on Canon Pixma MG6350, Canon technicians recommends to users some generic fixes for this problem. This recomendation like turn OFF of the printer and turn ON it.

If above does not help then please follow below:

Solution 1:

  1. Turn OFF the printer.
  2. Unplug the printer from the power source.
  3. Open the printer cover then reveal the ink cartridges.
  4. Remove the printhead from the printer be carefully.
  5. Clean the Printhead along with the Ink Cartridges.
  6. Clean the contact pads in the printer with a contact cleaner or a good pencil eraser.
  7. Reinstall the printhead again.
  8. Reinstall the ink cartridges thereafter before powering up the printer.
  9. Run the “Auto Head Alignment” for testing the printer.

Solution 2:

  1. Turn OFF Power of the Printer.
  2. Open the print head bay (as though you were about to change inks).
  3. Turn ON power.
  4. Wait for print carriage to start moving to the left and let it go past half way.
  5. Before print carriage reaches left hand side (but after going halfway across) shut the cover.
  6. Turned on the Printer again.

Solution 3:

  1. Open printer.
  2. Remove ink cartridges.
  3. Un-install printhead.
  4. Clean back of the printhead (electronic pins) with alcohol (isopropylen cleaning alcohol if possible). Make sure the pins are 100% clear.
  5. Turn off the printer (do not close it!) by plugging-off power cord (do not use power button).
  6. Clean electronic pins in printer (the pleace where you install printhead). Make sure its 100% clean.
  7. RE install printhead, then install ink cartridges.
  8. Plug in power cord.
  9. Turn printer ON normaly.
  10. Check if printer is working normaly (no errors).

Solution 4:

  1. Turn OFF the printer.
  2. Disconnect the printer from the power source.
  3. Open cover of the printer and remove the color cartridges.
  4. Remove the sled in which the cartridges were previously placed.
  5. clean the cartridges with water be carefully. For maximum results, clean it use isopropanol (there in the pharmacy), so that the printhead can not clog with lime.
  6. Make sure that the golden contacts are not wet, otherwise you can damage the print head.
  7. Dry everything be carefully, make sure no residual water gets into the printer.
  8. Reinstall cartridges and carriages in the first place.
  9. Turn ON the printer again.

If the message of "Error B200" appears again, the printer have to be switched off again. And The flap have to be opened before switching on. When switching ON again with the flip open, the printer then performs a self-test: Then the error should not occur to repeat more often, that it works and the problem solved.

Solution 5:

  1. Unplug the power cable.
  2. Open the printer.
  3. Push the whole print head mechanic to the center.
  4. While the printer still open, plug the power and turn it ON.
  5. When the printhead still moving and is going to the very LEFT, close the cover.
  6. Wait until its boot up.